3D打印技术在固体废弃物资源循环中的应用

摘要
图/表
参考文献
相关文章 (3)

全文: PDF (743 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要打印材料是限制3D打印技术发展和推广应用的瓶颈问题，目前已经发现部分固体废弃物与3D打印的契合度很高，可以用于制备3D打印材料.本文综述了4类可以用于3D打印的固体废弃物，包括硅铝基废弃物、农林废弃物、废旧塑料和废旧金属，着重讨论了这4类废弃物制备3D打印材料的方法以及废弃物的添加对原打印材料造成的影响，同时分析了当前废弃物制备3D打印材料需要解决的问题，并对废弃物基3D打印材料的发展趋势进行了展望.

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	张婉冰
	张付申

关键词 ： 3D打印, 硅铝基废弃物, 农林废弃物, 废旧塑料, 废旧金属, 资源绿色循环

Abstract：Printing material is the bottleneck problem limiting the development and industrial application of 3D printing technology. Thus far, it had been found that some solid wastes had high compatibility with 3D printing, which could be used to prepare 3D printing material. This paper reviewed four types of solid wastes which could be applied in 3D printing, including Si-Al based waste, agricultural and forestry waste, plastic waste and scrap metals. The methods of preparing 3D printing materials from these four types of wastes and the influence of wastes additions on the original printing materials were discussed emphatically. Meanwhile, the problems needed to be solved in the preparation of 3D printing materials from wastes were analyzed, and the development prospects of waste-based 3D printing materials was also articulated.

Key words： 3D printing Si-Al based waste agricultural and forestry waste plastic waste metal scraps green recycling of resource

收稿日期: 2020-10-28

PACS:

X705

基金资助:国家自然科学基金资助项目（51778606）；中国科学院绿色过程制造创新研究院自主部署联合基金项目（IAGM2020C23）；2020中央引导地方科技发展基金项目（2020ZY0032）

通讯作者: 张付申,研究员,fszhang@rcees.ac.cn E-mail: fszhang@rcees.ac.cn

作者简介: 张婉冰(1996-),女,河南商丘人,中国科学院生态环境研究中心硕士研究生,主要从事固体废弃物资源化研究.

引用本文:

张婉冰, 张付申. 3D打印技术在固体废弃物资源循环中的应用[J]. 中国环境科学, 2021, 41(5): 2299-2310. ZHANG Wan-bing, ZHANG Fu-shen. Application of 3D printing technology in the resource recycling of solid wastes. CHINA ENVIRONMENTAL SCIENCECE, 2021, 41(5): 2299-2310.

链接本文:

http://www.zghjkx.com.cn/CN/ 或 http://www.zghjkx.com.cn/CN/Y2021/V41/I5/2299

[1]	Kietzmann J, Pitt L, Berthon P. Disruptions, decisions, and destinations:Enter the age of 3-D printing and additive manufacturing[J]. Business Horizons, 2015,58(2):209-215.
[2]	Wong K V, Hernandez A. A review of additive manufacturing[J]. Isrn Mechanical Engineering, 2012,2012:30-38.
[3]	朱艳青,史继富,王雷雷,等.3D打印技术发展现状[J]. 制造技术与机床, 2015,(12):50-57. Zhu Y Q, Shi J F, Wang L L, et al. Current status of the three-dimensional printing technology[J]. Manufacturing Technology & Machine Tool, 2015,(12):50-57.
[4]	Zhang D, Chi B, Li B, et al. Fabrication of highly conductive graphene flexible circuits by 3D printing[J]. Synthetic Metals, 2016,217:79-86.
[5]	Kolarevic B. Digital fabrication manufacturing architecture in the information age[J]. Modeling and Fabrication, 2001,20:268-278.
[6]	Voon S L, An J, Wong G, et al. 3D food printing:a categorised review of inks and their development[J]. Virtual and Physical Prototyping, 2019,14(3):203-218.
[7]	Chia H N, Wu B M. Recent advances in 3D printing of biomaterials[J]. Journal of Biological Engineering, 2015,9(4):1-14.
[8]	Sakin M, Kiroglu Y C. 3D Printing of Buildings:Construction of the Sustainable Houses of the Future by BIM[J]. Energy Procedia, 2017,134:702-711.
[9]	陈硕平,易和平,罗志虹,等.高分子3D打印材料和打印工艺[J]. 材料导报, 2016,30(7):54-59. Chen S P, Ying H P, Luo Z H, et al. The 3DPrinting Polymers and Their Printing Technologies[J]. Materials Reports, 2016,30(7):54-59.
[10]	Agarwala M, Bourell D, Beaman J, et al. Direct selective laser sintering of metals[J]. Rapid Prototyping Journal, 1995,1(1):26-36.
[11]	Manapat J Z, Chen Q, Ye P, et al. 3D printing of polymer nanocomposites via stereolithography[J]. Macromolecular Materials and Engineering, 2017,302(9):1-16.
[12]	张学军,唐思熠,肇恒跃,等.3D打印技术研究现状和关键技术[J]. 材料工程, 2016,44(2):122-128. Zhang X J, Tang S Y, Zhao H Y, et al. Research Status and Key Technologies of 3D Printing[J]. Journal of Materials Engineering, 2016,44(2):122-128.
[13]	De Schutter G, Lesage K, Mechtcherine V, et al. Vision of 3D printing with concrete-Technical, economic and environmental potentials[J]. Cement and Concrete Research, 2018,112:25-36.
[14]	张以河,胡攀,张娜,等.铁矿废石及尾矿资源综合利用与绿色矿山建设[J]. 资源与产业, 2019,21(3):1-13. Zhang Y H, Hu P, Zhang N, et al. Comprehensive use of iron ore wastes and tailings and green mine construction[J]. Resources & Industries, 2019,21(3):1-13.
[15]	汤桂兰,胡彪,康在龙,等.废旧塑料回收利用现状及问题[J]. 再生资源与循环经济, 2013,6(1):31-35. Tang G L, Hu B, Kang Z L, et al. Current status and problems on waste plastic recycling[J]. Recyclable Resources and Circular Economy, 2013,6(1):31-35.
[16]	王金武,唐汉,王金峰.东北地区作物秸秆资源综合利用现状与发展分析[J]. 农业机械学报, 2017,48(5):1-21. Wang J L, Tang H, Wang J F. Comprehensive Utilization Status and Development Analysis of Crop Straw Resource in Northeast China[J]. Transactions of the Chinese Society for Agricultural Machinery, 2017,48(5):1-21.
[17]	薛亚洲,范继涛,王雪峰,等.北京等六省(市)矿山固废综合利用的思考[J]. 中国国土资源经济, 2018,31(1):19-23. Xue Y Z, Fang J T, Wang X F, et al. Thought on Comprehensive Utilization of Solid Wastes in Mines of Six Provinces (Cities) like Beijing in China[J]. Natural Resource Economics of China, 2018, 31(1):19-23.
[18]	Le T T, Austin S A, Lim S, et al. Hardened properties of high-performance printing concrete[J]. Cement and Concrete Research, 2012,42(3):558-566.
[19]	Panda B, Ruan S, Unluer C, et al. Improving the 3D printability of high volume fly ash mixtures via the use of nano attapulgite clay[J]. Composites Part B:Engineering, 2019,165:75-83.
[20]	Yu Y, Guo Y, Jiang T, et al. Laser sintering and post-processing of a walnut shell/Co-PES composite[J]. RSC Advances, 2017,7(37):23176-23181.
[21]	Idriss A I B, Li J, Wang Y, et al. Selective Laser Sintering (SLS) and Post-Processing of Prosopis Chilensis/Polyethersulfone Composite (PCPC)[J]. Materials, 2020,13(13):1-14.
[22]	Tran T N, Bayer I S, Heredia-Guerrero J A, et.al Cocoa shell waste biofilaments for 3D Printing applications[J]. Macromolecular Materials and Engineering, 2017,302(11):10-20.
[23]	Ferrari F, Esposito Corcione C, Montagna F, et al. 3D Printing of polymer waste for improving people's awareness about marine litter[J]. Polymers, 2021,12(8):1-14.
[24]	Kim H, Lee S. Printability and physical properties of iron slag powder composites using material extrusion-based 3D printing[J]. Journal of Iron and Steel Research International, 2021,28(1):111-121.
[25]	Hu W, Nie Q, Huang B, et al. Mechanical and microstructural characterization of geopolymers derived from red mud and fly ashes[J]. Journal of Cleaner Production, 2018,186:799-806.
[26]	Hu W, Nie Q, Huang B, et al. Investigation of the strength development of cast-in-place geopolymer piles with heating systems[J]. Journal of Cleaner Production, 2019,215:1481-1489.
[27]	Roussel N. Rheological requirements for printable concretes[J]. Cement and Concrete Research, 2018,112:76-85.
[28]	Panda B, Chandra Paul S, Jen Tan M. Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material[J]. Materials Letters, 2017,209:146-149.
[29]	Panda B, Unluer C, Tan M J. Extrusion and rheology characterization of geopolymer nanocomposites used in 3D printing[J]. Composites Part B:Engineering, 2019,176:1-9.
[30]	Khalil N, Aouad G, El Cheikh K, et al. Use of calcium sulfoaluminate cements for setting control of 3D-printing mortars[J]. Construction and Building Materials, 2017,157:382-391.
[31]	周伟,米红.中国能源消费排放的CO2测算[J]. 中国环境科学, 2010,30(8):1142-1148. Zhou W, Mi H. Calculation on enery-related CO2 emissions in China[J]. China Environmental Science, 2010,30(8):1142-1148.
[32]	劳德平,丁书强,倪文,等.响应面优化制备粉煤灰基PASC混凝剂性能与表征[J]. 中国环境科学, 2018,38(12):4599-4607. LAO D P DING S Q NI W et al. Response surface method optimization of preparation fly ash based polysilicate aluminum chloride coagulant:performance and microstructure characterization[J]. China Environmental Science, 2018,38(12):4599-4607.
[33]	姚志通.固体废弃物粉煤灰的资源化利用[D]. 杭州:浙江大学, 2010. Yao Z T. The resource utilization of solid waste coal fly ash[D]. Hangzhou:Zhejiang University, 2007.
[34]	Herath C, Gunasekara C, Law D W, et al. Performance of high volume fly ash concrete incorporating additives:A systematic literature review[J]. Construction and Building Materials, 2020,258:1-13.
[35]	Panda B, Tay Y W D, Paul S C, et al. Current challenges and future potential of 3D concrete printing[J]. Materialwissenschaft und Werkstofftechnik, 2018,49(5):666-673.
[36]	Long W J, Tao J L, Lin C, et al. Rheology and buildability of sustainable cement-based composites containing micro-crystalline cellulose for 3D-printing[J]. Journal of Cleaner Production, 2019, 239:118054-118067.
[37]	Laskar A I, Talukdar S. Rheological behavior of high performance concrete with mineral admixtures and their blending[J]. Construction and Building Materials, 2008,22(12):2345-2354.
[38]	Jalal M, Fathi M, Farzad M. Effects of fly ash and TiO2 nanoparticles on rheological, mechanical, microstructural and thermal properties of high strength self compacting concrete[J]. Mechanics of Materials, 2013,61:11-27.
[39]	Bentz D P, Ferraris C F, Galler M A, et al. Influence of particle size distributions on yield stress and viscosity of cement-fly ash pastes[J]. Cement and Concrete Research, 2012,42(2):404-409.
[40]	Jiao D, Shi C, Yuan Q, et al. Effect of constituents on rheological properties of fresh concrete-A review[J]. Cement and Concrete Composites, 2017,83:146-159.
[41]	Li Y, Chen B. Factors that affect the properties of magnesium phosphate cement[J]. Construction and Building Materials, 2013, 47:977-983.
[42]	Xu B, Ma H, Shao H, et al. Influence of fly ash on compressive strength and micro-characteristics of magnesium potassium phosphate cement mortars[J]. Cement and Concrete Research, 2017,99:86-94.
[43]	Alal M, Mansouri E. Effects of fly ash and cement content on rheological, mechanical, and transport properties of high-performance self-compacting concrete[J]. Science and Engineering of Composite Materials, 2012,19(4):393-405.
[44]	Panda B, Tan M J. Experimental study on mix proportion and fresh properties of fly ash based geopolymer for 3D concrete printing[J]. Ceramics International, 2018,44(9):10258-10265.
[45]	Weng Y, Ruan S, Li M, et al. Feasibility study on sustainable magnesium potassium phosphate cement paste for 3D printing[J]. Construction and Building Materials, 2019,221:595-603.
[46]	Gosselin C, Duballet R, Roux P, et al. Large-scale 3D printing of ultra-high performance concrete-a new processing route for architects and builders[J]. Materials & Design, 2016,100:102-109.
[47]	Khoshnevis B. Automated construction by contour crafting-related robotics and information technologies[J]. Automation in Construction, 2004,13(1):5-19.
[48]	Hanif A, Lu Z, Li Z. Utilization of fly ash cenosphere as lightweight filler in cement-based composites-A review[J]. Construction and Building Materials, 2017,144:373-384.
[49]	Hanif A, Lu Z, Diao S, et al. Properties investigation of fiber reinforced cement-based composites incorporating cenosphere fillers[J]. Construction and Building Materials, 2017,140:139-149.
[50]	Lu B, Qian Y, Li M, et al. Designing spray-based 3D printable cementitious materials with fly ash cenosphere and air entraining agent[J]. Construction and Building Materials, 2019,211:1073-1084.
[51]	Pal S C, Mukherjee A, Pathak S R. Investigation of hydraulic activity of ground granulated blast furnace slag in concrete[J]. Cement and Concrete Research, 2003,33(9):1481-1486.
[52]	Pal S C, Mukherjee A, Pathak S R. Investigation of hydraulic activity of ground granulated blast furnace slag in concrete[J]. Cement and Concrete Research, 2003,33(9):1481-1486.
[53]	Park C K, Noh M H, Park T H, Rheological properties of cementitious materials containing mineral admixtures[J]. Cement and Concrete Research, 2005,35(5):842-849.
[54]	Jiang H, Fall M, Yilmaz E, et al. Effect of mineral admixtures on flow properties of fresh cemented paste backfill:Assessment of time dependency and thixotropy[J]. Powder Technology, 2020,372:258-266.
[55]	Panda B, Ruan S, Unluer C, et al. Investigation of the properties of alkali-activated slag mixes involving the use of nanoclay and nucleation seeds for 3D printing[J]. Composites Part B:Engineering, 2020,186:107826-1078313.
[56]	Nath P, Sarker P K. Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition[J]. Construction and Building Materials, 2014,66:163-171.
[57]	Garcia Lodeiro I, Palomo A, Fernández-Jiménez A, et al. Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram Na2O-CaO-Al2O3-SiO2-H2O[J]. Cement and Concrete Research, 2011,41(9):923-931.
[58]	Gräfe M, Power G, Klauber C. Bauxite residue issues:Ⅲ. Alkalinity and associated chemistry[J]. Hydrometallurgy, 2011,108(1/2):60-79.
[59]	Power G, Gräfe M, Klauber C. Bauxite residue issues:I. Current management, disposal and storage practices[J]. Hydrometallurgy, 2011,108(1/2):33-45.
[60]	Ruyters S, Mertens J, Vassilieva E, et al. The red mud accident in Ajka (Hungary):Plant toxicity and trace metal bioavailability in red mud contaminated soil[J]. Environmental Science & Technology, 2011, 45(4):1616-1622.
[61]	Bayat A, Hassani A, Yousefi A A. Effects of red mud on the properties of fresh and hardened alkali-activated slag paste and mortar[J]. Construction and Building Materials, 2018,167:775-790.
[62]	Reddy P S, Reddy N G, Serjun V Z, et al. Properties and assessment of applications of red mud (bauxite residue):Current status and research needs[J]. Waste and Biomass Valorization, 2020,12(3):1185-1217.
[63]	Ribeiro D V, Silva A S, Labrincha J A, et al. Rheological properties and hydration behavior of portland cement mortars containing calcined red mud[J]. Canadian Journal of Civil Engineering, 2013,40(6):557-566.
[64]	Senff L, Hotza D, Labrincha J A. Effect of red mud addition on the rheological behaviour and on hardened state characteristics of cement mortars[J]. Construction and Building Materials, 2011,25(1):163-170.
[65]	裴德健.利用冶金渣制备硅钙基多元体系陶瓷的机理及应用研究[D]. 北京:北京科技大学, 2019. Pei D J. Study on the mechanism and application of Si-Ca multielement ceramics prepared from metallurgical slags[D]. University of Science and Technology Beijing, 2019.
[66]	芦令超,陈明旭,李来波,等.一种赤泥3D打印碱激发胶凝材料及其使用方法:中国, 109721298A[P]. 2019-10-15. Lu L C, Chen M X, Li LB, et al. A kind of red mud 3D printing alkali-activated gelling material and Instructions:China, 109721298A[P]. 2019.
[67]	贺深阳,蒋述兴,汪文凌.我国赤泥建材资源化研究进展[J]. 轻金属, 2007,(12):1-5. He S Y, Jiang S X, Wang W L. Research progress of utilizing red mud as resource of building material in China[J]. Light Metals, 2007, (12):1-5.
[68]	Rahman M K, Baluch M H, Malik M A. Thixotropic behavior of self compacting concrete with different mineral admixtures[J]. Construction and Building Materials, 2014,50:710-717.
[69]	Ahari R S, Erdem T K, Ramyar K. Thixotropy and structural breakdown properties of self consolidating concrete containing various supplementary cementitious materials[J]. Cement and Concrete Composites, 2015,59:26-37.
[70]	Baghabra Al-Amoudi O S, Maslehuddin M, Abiola T O. Effect of type and dosage of silica fume on plastic shrinkage in concrete exposed to hot weather[J]. Construction and Building Materials, 2004,18(10):737-743.
[71]	Cohen M D, Olek J, Dolch W L. Mechanism of plastic shrinkage cracking in portland cement and portland cement-silica fume paste and mortar[J]. Cement and Concrete Research, 1990,20(1):103-119.
[72]	Tadros T F. Surface and colloid chemistry in advanced ceramics processing[J]. Advances in Colloid and Interface Science, 1995, 61:192-193.
[73]	Senff L, Labrincha J A, Ferreira V M, et al. Effect of nano-silica on rheology and fresh properties of cement pastes and mortars[J]. Construction and Building Materials, 2009,23(7):2487-2491.
[74]	Kruger J, Zeranka S, Van Zijl G. An ab initio approach for thixotropy characterisation of (nanoparticle-infused) 3D printable concrete[J]. Construction and Building Materials, 2019,224:372-386.
[75]	Cheah C B, Samsudin M H, Ramli M, et al. The use of high calcium wood ash in the preparation of Ground Granulated Blast Furnace Slag and Pulverized Fly Ash geopolymers:A complete microstructural and mechanical characterization[J]. Journal of Cleaner Production, 2017, 156:114-123.
[76]	Deb P S, Nath P, Sarker P K. The effects of ground granulated blast-furnace slag blending with fly ash and activator content on the workability and strength properties of geopolymer concrete cured at ambient temperature[J]. Materials & Design (1980~2015), 2014, 62:32-39.
[77]	Walling S A, Provis J L. Magnesia-based cements:A journey of 150years, and cements for the future?[J]. Chemical Reviews, 2016, 116(7):4170-204.
[78]	Jo B W, Kim C H, Tae G H, et al. Characteristics of cement mortar with nano-SiO2 particles[J]. Construction and Building Materials, 2007,21(6):1351-1355.
[79]	田赟,王海燕,孙向阳,等.农林废弃物环保型基质再利用研究进展与展望[J]. 土壤通报, 2011.42(2):497-502. Tian Y, Wang H Y, Sun X Y, et al. The Progress and Prospects of Agricultural and Forest Residue Substrate[J]. Chinese Journal of Soil Science, 2011,42(2):497-502.
[80]	Muizniecea I, Dace E, Blumberga D. Dynamic modeling of the environmental and economic aspects of bio-resources from agricultural and forestry wastes[J]. Procedia Earth and Planetary Science, 2015,15:806-812.
[81]	Dhinakaran V, Manoj Kumar K P, Bupathi Ram P M, et al. A review on recent advancements in fused deposition modeling[J]. Materials Today:Proceedings, 2020,27:752-756.
[82]	Chen Z W, Li Z Y, Li J J, et al. 3D printing of ceramics:A review[J]. Journal of the European Ceramic Society, 2019,39(4):661-687.
[83]	Vyavahare S, Teraiya S, Panghal D, et al. Fused deposition modelling:a review[J]. Rapid Prototyping Journal, 2020,26(1):176-201.
[84]	Hague R, D'costa G, Dickens P M. Structural design and resin drainage characteristics of QuickCast 2.0[J]. Rapid Prototyping Journal, 2001,7(2):66-73.
[85]	Childs T H C, Berzins M, Ryder G R, et al. Selective laser sintering of an amorphous polymer-simulations and experiments[J]. Proceedings of the Institution of Mechanical Engineers, Part B:Journal of Engineering Manufacture, 2005,213(4):333-349.
[86]	Schmidt M, Pohle D, Rechtenwald T. Selective laser sintering of PEEK[J]. CIRP Annals, 2007,56(1):205-208.
[87]	Salman O O, Brenne F, Niendorf T, et al. Impact of the scanning strategy on the mechanical behavior of 316L steel synthesized by selective laser melting[J]. Journal of Manufacturing Processes, 2019,45:255-261.
[88]	Qian B, Shen Z. Laser sintering of ceramics[J]. Journal of Asian Ceramic Societies, 2018,1(4):315-321.
[89]	Nitz H, Semke H, Landers R, et al. Reactive extrusion of polycaprolactone compounds containing wood flour and lignin[J]. Journal of Applied Polymer science, 2010,81(8):1972-1984.
[90]	Tran T N, Heredia-Guerrero J A, Mai B T, et al. Bioelastomers based on cocoa shell waste with antioxidant ability[J]. Advanced Sustainable Systems, 2017,1(7):1-11.
[91]	Mourshed M, Masud M H, Rashid F, et al. Towards the effective plastic waste management in Bangladesh:a review[J]. Environmental Science and Pollution Research, 2017,24(35):27021-27046.
[92]	Incekara E. Composite material used to produce a filament as raw material of an object to be configured with specific FDM type dimensioned printer contains at least thermoplastic polymer and waste polyurethane reinforced of thermoset feature:WO2020142031-A2[P]. 2020-07-09.
[93]	耿晓梦,赵由才,夏旻,等.存余垃圾中废旧塑料性能演变及资源转化探讨[J]. 中国环境科学, 2021,41(1):273-278. Geng X M, Zhao Y C, Xia Y, et al. Characteristics variation and reutilization technology of waste plastics in aged refuse[J]. China Environmental Science, 2021,41(1):273-278.
[94]	Schjøtt-Pedersen N, Welo T, Ringen G, et al. Using set-based design for developing a 3D metal forming process[J]. Procedia CIRP, 2019,84:149-154.
[95]	耿泽昊.金属抛光粉尘湿法处理系统的开发与试验研究[D]. 镇江:江苏大学, 2018. Geng Z H. Design & Experiment Investigation on Metal Burnishing Dust Wet Removal System[D]. Zhenjiang:Jiangsu University, 2018.
[96]	Song M, Zhang X, Zhang Y, et al. Performing a regeneration method for 3D printing to recycle metal powder involves collecting and sieving waste metal powder in a vacuum or atmosphere protection environment, and sieving recycled metal powder to remove large particles:CN210786616-U[P]. 2020-06-23.
[97]	Debroy T, Wei H L, Zuback J S, et al. Additive manufacturing of metallic components-Process, structure and properties[J]. Progress in Materials Science, 2018,92:112-224.
[98]	Matthews M J, Guss G, Khairallah S A, et al. Denudation of metal powder layers in laser powder bed fusion processes[J]. Acta Materialia, 2016,114:33-42.
[99]	段宣政,赵菲,王淑丹,等.国内外金属3D打印材料现状与发展[J]. 焊接, 2020,(2):49-55,68. Duan X Z, Zhao F, Wang S D, et al. Current situation and development of 3D printing materials for metal at home and abroad[J]. Welding & Joining, 2020,(2):49-55,68.
[100]	Basak A, Das S. Epitaxy and microstructure evolution in metal additive manufacturing[J]. Annual Review of Materials Research, 2016,46(1):125-149.